Download Taylor PDF

TitleTaylor
File Size1.5 MB
Total Pages52
Table of Contents
                            opCvr
refpg
TOC
1-5
6-9
prtL
                        
Document Text Contents
Page 1

Models 336, 338 & 339

Freezemaster
300 Series

Original Operating Instructions

036029--M
4/16/09 (Original Publication)

(Updated 11/1/11)

Page 2

Complete this page for quick reference when service is required:

Taylor Distributor:

Address:

Phone:

Service:

Parts:

Date of Installation:

Information found on the data label:

Model Number:

Serial Number:

Electrical Specs: Voltage Cycle

Phase

Maximum Fuse Size: A

Minimum Wire Ampacity: A

E April, 2009 Taylor
All rights reserved.
036029--M

The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.

Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072

Page 26

22 Models 336, 338 & 339Operating Procedures

Step 5
Press the “AUTO” button. The “AUTO” light will come
on indicating the main refrigeration system is
operating. When the unit cycles off, the product will be
at serving viscosity.

Figure 37

Note: The mix refrigeration light will come on,
indicating the mix refrigeration system is operating to
maintain the mix in the mix hopper.

Step 6
Fill the hopper with mix. As the mix level comes in
contact with the mix level sensing probe on the rear
wall of the hopper, the “MIX LOW” light will shut off.

Step 7
Place the mix hopper cover in position over the mix
hopper.

Repeat Steps 1 through 7 for the other side of the
freezer.

Closing Procedure

To disassemble your unit, the following items will be
needed:

S Two cleaning pails
S Sanitized stainless steel rerun can with lid
S Necessary brushes (provided with freezer)
S Cleaner
S Single service towels

Draining Product From the
Freezing Cylinder
Step 1
Press the “AUTO” button, cancelling compressor and
beater motor operation.

Press the mix refrigeration button, cancelling the mix
hopper refrigeration system.

Step 2
Remove the hopper cover, hopper gasket and air tube.
Take these parts to the sink for cleaning.

Step 3
If local health codes permit the use of rerun, place
a sanitized, NSF approved stainless steel rerun
container beneath the door spout. Press the WASH
key and lower the draw handle. Drain the remaining
product from the freezing cylinder and mix hopper.
When the flow of product stops, press the WASH key
and raise the draw handle. Place the sanitized lid on
the rerun container and place it in the walk--in cooler.

Note: If local health codesDONOTpermit theuse
of rerun, the product must be discarded. Drain the
product into a mix pail and properly discard it.

Repeat Steps 1 through 3 for the other side of the
freezer.

Note: For the Model 336, both sides must be in
WASH. If one side is in AUTO and the other is in
WASH, the side that is in WASH will continue to freeze.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Rinsing
Step 1
Pour two gallons (7.6 liters) of cool clean water into the
mix hopper. With the brushes provided, scrub the mix
hopper, mix inlet hole and mix level sensing probe.

Step 2
With a pail beneath the door spout, raise the primeplug
and press the “WASH” button.

Step 3
When a steady stream of rinse water is flowing from
the prime plug opening in the bottom of the freezer
door, lower the draw handle. Drain all the rinse water
from the freezing cylinder, raise the draw handle and
press the “WASH” button, cancelling the “WASH”
mode.

Repeat Steps 1 through 3 for the other side of the
freezer.

Page 27

23Models 336, 338 & 339 Operating Procedures

Cleaning
Step 1
Prepare a pail of approved 100 PPM cleaning solution
(examples: 2--1/2 gal. [9.5 liters] of Kay--5R or 2 gal.
[7.6 liters] of Stera--SheenR ). USE WARM WATER
AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS.

Step 2
Push down the prime plug. Pour the cleaning solution
into the mix hopper.

Step 3
While the solution is flowing into the freezing cylinder,
brush clean the mix hopper, mix level sensing probe,
and the mix inlet hole.

Step 4
Press the “WASH” button. This will cause the cleaning
solution in the freezing cylinder to agitate.

Step 5
Place an empty pail beneath the door spout and raise
the prime plug.

Step 6
When a steady stream of cleaning solution is flowing
from the prime plug opening in the bottom of the
freezer door, lower the draw handle. Draw off all of the
solution.

Step 7
Once the cleaner stops flowing from the door spout,
raise the draw handle and press the “WASH” button,
cancelling the “WASH” mode.

Repeat Steps 1 through 7 for the other side of the
freezer.

Disassembly
Step 1

BE SURE THE POWER SWITCH IS IN THE
“OFF” POSITION. MAKE SURE NO LIGHTS ARE
LIT ON THE CONTROL PANEL.

Step 2
Remove the handscrews, freezer door, beaters,
scraper blades, and drive shafts from the freezing
cylinders. Take these parts to the sink for cleaning.

Step 3
Remove the front drip tray and the splash shield.

Brush Cleaning

Step 1
Prepare a sink with an approved cleaning solution
(examples: Kay--5R or Stera--SheenR ). USE WARM
WATER AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS. If another approved cleaner is
used, dilute it according to the label instructions.
(IMPORTANT: Follow the label directions. Too
STRONG of a solution can cause parts damage, while
too MILD of a solution will not provide adequate
cleaning.) Make sure all brushes provided with the
freezer are available for brush cleaning.

Step 2
Remove the seals from the drive shafts.

Step 3
From the freezer door remove:

S gaskets
S front bearings
S pivot pins
S adjustable draw handles
S design caps
S draw valves
S prime plugs

Remove all o--rings.

Note: To remove o--rings, use a single service towel
to grasp the o--ring. Apply pressure in an upward
direction until the o--ring pops out of its groove. With
the other hand, push the top of the o--ring forward and
it will roll out of the groove and can be easily removed.
If there is more than one o--ring to be removed, always
remove the rear o--ring first. This will allow the o--ring
to slide over the forward rings without falling into the
open grooves.

Page 51

Model 339
046585--33
Rev. 8/11

Page 52

Model 339
046585-62
Rev. 8/11

Similer Documents